When I think about a bridge, I picture the people who build it before I picture the steel. A crew reaches the site at dawn, a crane operator checks the load, a supervisor walks the edge of the deck, and each of them expects to go home when the day ends. That picture stays with me whenever I think about construction site safety, and it’s why I wanted to look closely at a company that’s been building bridges, roads, and ports in Nigeria since 1965.
Julius Berger’s first project in Nigeria began in August 1965, with a contract for a bridge in Lagos that later became the Eko Bridge. Since then, the public record has gathered company statements about its safety performance, a milestone at one of its sites, and an award from a professional body. I read those alongside independent reports on construction site safety in Nigeria, and I’ve kept to what the sources say.
This is a case study, and its purpose is learning. I’m describing what’s been published, and I don’t judge any company or the people who work for it.
Here’s what we’ll cover: how Julius Berger built its place in Nigeria, what the company has said about its safety performance, why construction site safety is still a concern across the country, the hazards a site has to control, how a workplace safety management system holds the work together, three lessons from the public record, and how ISO 45001 applies to construction companies in Nigeria.
Note: I last checked every source in this article in November 2026. Safety figures, company statements, and regulations can change, so it’s worth confirming anything you plan to act on.
Key Takeaways
- Julius Berger’s first project in Nigeria began in 1965, and it’s been building bridges, roads and port works across the country ever since.
- The company says its lost time injury frequency has stayed among the lowest in the industry for years. I found no published figures to check that against, so I treat it as the company’s own statement.
- The managing director of the Nigeria Social Insurance Trust Fund (NSITF) cited over 150 construction site fatalities in 2024, attributing the figure to the Nigerian Safety Commission.
- A workplace safety management system gives a site a written way to find hazards, set controls, check them and fix problems, including the ones subcontractors bring.
- ISO 45001 gives that system a recognized structure, and a company can follow its principles with or without certification, which is what Julius Berger said it was doing in September 2025 while working toward certification.
How Has Julius Berger Built Its Place in Nigeria Over Six Decades?
The story started in Lagos in August 1965. That month, a contract for the Second Mainland Bridge was signed between the Nigerian Ministry of Public Works and the German parent company, Julius Berger Tiefbau AG. The bridge later became known as the Eko Bridge, and its first phase was completed in 1968. The company’s own history describes its Nigerian business as having begun as a project vehicle for that bridge.
Julius Berger Nigeria Ltd. was formally incorporated in February 1970, and it marked its golden jubilee at its 2020 annual general meeting. It became a public limited company in 1991. Each of these projects was built by crews whose names rarely appear in a company timeline, and I think of them as I read the dates.
What Kinds of Projects Has the Company Taken On?
The early record shows how varied the work was. In 1970, for instance, the company repaired the Onitsha Bridge in seven weeks using a temporary Bailey structure, which is a prefabricated steel bridge that can be assembled quickly. In 1975 it was awarded the contract for the Lagos Inner Ring Road, with work starting in 1976. It also took on the Tin Can Island port extension in 1976, and the same brochure says the port was commissioned with eight berths only 18 months after the project began.
Later projects include the Third Mainland Bridge, which Wikipedia describes as about 11.8 kilometres long across the Lagos Lagoon, linking Lagos Island and the mainland. Julius Berger took part in building it. The brochure also lists the Lekki-Ikoyi Link Bridge, awarded in 2009, and the Lagos-Badagry Road expansion, which began that year.
That’s a broad record, so let’s now see what the company itself has said about its safety performance.
What Has Julius Berger Said About Its Safety Performance?
In September 2025, the Institute of Safety Professionals of Nigeria (ISPON) presented Julius Berger with its Corporate Leadership Award in Health, Safety and Environment at the 2025 Safety Summit in Abuja. ISPON credited the company with consistently maintaining one of the lowest lost time injury frequencies in the construction industry. The company’s Director of Administration, Dr Abdulaziz Kaita, said the same frequency has remained one of the lowest in the industry for years. Neither report gives a figure, so I can’t check the statement against numbers, and I’m treating it as what it is: the company’s own account, backed by a professional body’s recognition.
The same reports say the company had implemented the principles of ISO 45001 (occupational health and safety) and ISO 14001 (environmental management), and that it was going through certification for both. A June 2026 report says the company has since been certified to ISO 14001 by a certification body called TVECert. That’s the only report of it I found, and I found nothing either way on ISO 45001 certification.
What Does a Lost Time Injury Frequency Rate Measure?
Since the company talks about lost time injury frequency, it helps to know what the term means. A lost time injury is a work injury that keeps someone away from work for at least a day or shift, and Safe Work Australia’s definition says that includes fatalities and permanent disability. The frequency rate divides the number of those injuries by the hours worked and multiplies the result by 1,000,000, which lets a small crew and a large company be compared on the same footing. The reports I read don’t say which definition Julius Berger uses, so it’s worth asking how a company counts before you compare two figures.
What Does 3,000,000 Hours Without a Lost Time Injury Tell Us?
In August 2023, the company’s Lagos Facility Works team marked 3,000,000 safe man-hours without a lost time injury and received the Managing Director’s Safety Award. A man-hour is one person working for one hour. For scale, a crew of 500 people who each work about 2,000 hours a year would take around three years to reach that total, so it’s a long run of ordinary working days and well worth recognizing. A manager quoted in the report said the company will aim to achieve zero injury.
A good rule of thumb for any milestone like this is to ask what the measure counts and what it leaves out. This one counts injuries that cost working time. It doesn’t tell us how many near misses happened, how many hazards were found and fixed, or how anyone’s health fared over the years.
Those are the company’s statements and milestones, so let’s look at the wider picture of construction site safety in Nigeria to see why they matter.
Why Is Construction Site Safety Still a Concern in Nigeria?
At the Federation of Construction Industry’s 69th annual general meeting in Abuja, reported in September 2025, the managing director of the NSITF said the Nigerian Safety Commission had reported over 150 fatalities linked to construction site accidents in 2024. He also estimated that the country averages 50 to 70 major construction accidents a year, though the report gives no source for that estimate. He called for rigorous safety audits, compliance with standards and ongoing capacity building.
What Causes Safety Violations on Nigerian Construction Sites?
Researchers have looked at this from several angles. One qualitative study, Investigating Safety Violations on Nigerian Construction Sites, used 30 interviews and observation of eight construction sites and grouped the causes into human, technical, and management or government causes. A 2021 questionnaire survey in Nigeria, Impediments to Construction Safety Improvement, named three major obstacles: limited dedication from project stakeholders, health and safety rules that don’t work effectively, and insufficient safety training for construction professionals.
Human factors are one part of the picture. At a Lagos State Safety Commission workshop for contractors, a retired commission director was quoted by the Guardian as saying that more than 80 per cent of recorded accidents and disasters are caused by human error, and the commission’s Director General urged contractors to address hazards that haven’t been identified or reduced. Read next to the studies above, that suggests the people on site, the way the site is set up and the systems around them all play a part.
How Common Are Hazards on Lagos Residential Sites?
A 2020 study in Acta Structilia surveyed supervisors at 255 of the 511 residential construction sites it identified in Lagos. About 91% of respondents had witnessed hazards of varying degrees. The researchers also compared one month of records: sites supervised by individuals or owners had about 25.3 more near misses and 12.4 more accidents per month than sites supervised by trained supervisors. A near miss is an event that could have caused harm but didn’t. The study shows a link and doesn’t prove a cause on its own, but it points to supervisor training as a sensible place to start.
What Are Regulators in Nigeria Asking of Construction Companies?
The Federal Ministry of Labour’s Occupational Safety and Health Department says it’s guided by the Factories Act (CAP F1, Laws of the Federation of Nigeria, 2004) and the National Policy on Occupational Safety and Health. It carries out inspections, workplace safety and health audits and investigations of accidents and dangerous occurrences, and it registers factory premises. The page doesn’t say which parts apply to construction sites, so a company should confirm how the rules apply to its own work.
In Lagos, the State Safety Commission’s performance report, presented in May 2026, said that more than 2,800 construction sites and facilities were found to violate safety regulations and that more than 3,500 construction sites received safety compliance certification.
In November 2024, a report carried by QED.ng, citing Punch, said the Lagos State Safety Commission had sanctioned Julius Berger after an engineer died at an Ijora facility in September. The commission asked the company to review its risk assessment, job hazard analysis and loading and offloading procedures, and to train staff involved in that work. I didn’t find a statement from the company, and the details of the sanction weren’t made public in the report I read.
What Hazards Does Construction Site Safety Have to Control?
Every site has its own mix of hazards, shaped by the work, the weather and the people on it, so the first job is writing a list for that site. A few categories turn up so often that safety teams give them special attention.
What Are the Most Common Construction Site Hazards?
OSHA, the US workplace safety regulator, built its Construction Focus Four training around four hazards: falls, being struck by objects or vehicles, being caught in or between equipment or objects, and electrocution. In plain terms, that means people falling from a height, being hit by something that moves or drops, being crushed or pinched, and coming into contact with electricity. OSHA is an American agency, and Nigerian rules differ, but these are physical hazards that exist on any site.
How Should Teams Control Work at Height?
OSHA says falls are the leading cause of death in construction, and it gives employers a three-step message: plan the job so it’s done safely, provide the right fall protection and equipment, and train every worker to use it. Its figures come from the US, where 389 of 1,034 construction deaths in 2024 were falls to a lower level, so they won’t transfer directly to Nigeria.
The hierarchy of controls from the US National Institute for Occupational Safety and Health (NIOSH) shows how to choose between options. In order, from most to least effective, they are elimination, substitution, engineering controls, administrative controls and personal protective equipment. For instance, assembling a section at ground level removes the need to work at height at all, which is elimination. A guardrail is an engineering control, and a harness is protective equipment, which sits last because it only works when it’s used correctly every time.
What Health Risks Build Up Over Time?
Some hazards harm slowly. OSHA lists sawing brick or concrete, drilling into concrete walls and grinding mortar among the activities that create respirable crystalline silica dust, and it says breathing that dust raises the risk of silicosis, lung cancer, chronic obstructive pulmonary disease and kidney disease. Silicosis is an incurable lung disease. A site’s risk assessment should also look at noise, heat and heavy lifting, which add up over time in the same way.
What Extra Risks Come With Road and Bridge Work Zones?
Road and bridge work brings vehicles into the picture. OSHA’s page on construction vehicle safety says a worker is just as likely to be struck by construction equipment inside the work zone as by passing traffic, and it cites a NIOSH publication saying vehicles and equipment in and around the work zone are involved in over half of worker fatalities. Workers share that space with passing motorists, construction vehicles and equipment at the same time. These sources are American, so the percentages won’t carry over to Nigeria, but the physical hazards are the same.
Hazards are only half the picture. A site also needs a way to find them, control them and check that the controls keep working, and that’s what a workplace safety management system does.
What Is a Workplace Safety Management System for Construction?
A workplace safety management system for construction is the set of written routines a company uses to find hazards on a site, decide how to control them, check that the controls are working and fix what the checks turn up. Many systems follow a four-stage cycle called Plan, Do, Check, Act. The company plans by listing hazards and setting goals, does the work with controls in place, checks results through inspections and audits, and acts on what it finds before the cycle starts again.
Because the routines are written down, a new supervisor, a client or an inspector can see how the site manages its risks without relying on one person’s memory. The tools below are the ones I’d look at first, since they turn up on most construction sites.
What Should a Site Safety Plan Include?
A site safety plan records how a project will manage its main health and safety risks. In the UK it’s called a construction phase plan, and under UK rules it has to be drawn up before the site is set up, by the principal contractor when more than one contractor is involved. Based on guidance from the UK Health and Safety Executive (HSE), the plan covers a description of the project, including key dates and key members of the team, and how the work will be managed. That second part covers the project’s health and safety aims, site rules, how the team will coordinate, how workers will be involved, site induction, welfare facilities and fire and emergency procedures. It also covers controls for any specific risks the work brings.
The same source says the plan should be easy to understand and as simple as possible. It shouldn’t carry generic risk assessments, records of how decisions were reached or detailed method statements. I didn’t find a Nigerian rule that uses the same name, so I’d treat this as a good model and check with the regulator on what applies to your project.
What Are a Job Hazard Analysis and a Permit to Work?
A job hazard analysis is, in OSHA’s words, a technique that focuses on job tasks to identify hazards before they occur. OSHA describes four steps. First, select the job, starting with the ones that carry the most risk. Next, break the job into steps by watching the work being done. Then, for each step, ask what could go wrong and how. Finally, decide on controls, using the same order of effectiveness we looked at earlier, with engineering controls ahead of procedures and protective equipment last.
A permit to work is a different tool. Guidance from the University of Cambridge describes it as a formal written instruction on the precautions to take for potentially hazardous work, such as hot work, confined spaces, roof access and demolition. It isn’t an instruction on how to do the task. One person with real authority issues the permit, and the person doing the work signs to accept its conditions. The permit lasts for a set time, it can’t be post-dated, and it’s closed only once the work is finished and has been checked. The same guidance warns that issuing a permit doesn’t make a job safe by itself, so the conditions on it have to be checked in practice.
Put together, the job hazard analysis looks at how a task can be done safely, and the permit controls when and under what conditions the riskiest tasks may start.
How Do Inductions and Toolbox Talks Keep Everyone Informed?
A site induction is the process of making sure workers are fully informed about how the site is organized and run. The source lists topics such as site layout, welfare facilities and rules, key people like supervisors and first aiders, emergency procedures and muster points, protective equipment, work at height and how to report incidents. It also says an induction should be prepared for the project in question rather than copied from a generic format, that attendance should be recorded, and that some check of understanding is ideal.
A toolbox talk is a different tool again. HSE defines it as a short presentation to the workforce on a single aspect of health and safety, and its examples include ladders, manual handling and roof work. HSE doesn’t set a length for these talks. A reasonable pattern is to give the induction on arrival and then use toolbox talks for the hazards of the week’s work.
With those everyday tools in view, let’s go back to Julius Berger’s public record and see what lessons a site can take from it.
3 Lessons in Construction Site Safety From Julius Berger’s Public Record
The company’s public statements can’t tell us how it runs each site day to day, so I’m treating them as prompts. Each lesson below starts from something the company has said and then looks at what a site of any size can do with it.
Lesson 1: Turn the Aim of Zero Injury Into a Measurable Objective
In the report on the 3,000,000-hour milestone, a manager said the company will aim to achieve zero injury. That’s a clear aim, but a site can’t check it on a Tuesday afternoon. ISO 45001 asks organizations to set occupational health and safety objectives (clause 6.2) and, where practicable, to make them measurable. For instance, a site might aim to have every permit to work checked on the day it’s issued, to inspect every scaffold each week, or to close every near-miss action within 14 days. Each objective needs an owner and a date, so someone can say at the end of the month whether it was met.
Lesson 2: Put the System in Place Before the Certificate
In September 2025, the company’s Director of Administration said it had implemented the principles of ISO 45001 and ISO 14001 and was going through certification. The order matters for any site. Certification is a separate step carried out by an outside body, and the routines it looks for, such as hazard lists, permits, inductions, inspections and corrective actions, can start long before an audit is booked. A site that begins with those routines can show an auditor, a client or a regulator how it works, whether or not it later seeks a certificate.
Lesson 3: Keep Competence Current
In the same report, the Director said membership of the Institute of Safety Professionals of Nigeria is a legal requirement before employment for safety practitioners, and that members are sponsored every year to attend its conferences. I couldn’t confirm the membership requirement beyond his statement, so it’s worth checking the Institute’s own rules before relying on it. The practical point holds either way. ISO 45001 asks organizations to determine the competence their workers need (clause 7.2) and to keep evidence of it. A simple training record that lists each person’s qualifications, the date of their last refresher and the date the next one is due makes that easy to check.
What Are the Core Elements of a Construction Safety Management System?
The tools above work only when the people around them know their roles. Three arrangements deserve attention on a construction site: who is responsible for what, how outside firms are managed, and how the site prepares for an emergency.
Who Is Responsible for Safety on a Construction Site?
ISO 45001 asks top management to show leadership and commitment (clause 5.1), to assign roles, responsibilities and authorities (clause 5.3) and to consult workers and involve them in decisions (clause 5.4). On a site, that usually works out as follows. Senior managers set the policy and provide the time, money and people. The site manager runs the plan day to day. Supervisors check the work as it happens, the safety officer advises and inspects, and workers follow the controls and report hazards.
A one-page responsibility chart helps. For each control, it lists a named owner, a backup, what they check and how often. Many sites also make it clear that any worker may stop a task that looks unsafe, and that reporting a hazard will never count against them.
How Do You Manage Subcontractors on Site?
Most construction sites have several firms working at once, and a hazard created by one crew can hurt another. OSHA’s multi-employer policy puts a name to this. In a letter explaining the policy, OSHA describes a controlling employer as one with overall oversight of the worksite, including the power to fix violations or to require others to fix them. Such an employer can be cited only if it failed to exercise reasonable care. This is an American policy, and Nigerian law may handle it differently, but it shows why a main contractor needs to know what its subcontractors are doing.
A practical approach covers the following steps:
- Ask for a subcontractor’s safety record and training before awarding the work.
- Share the site safety plan and induct every worker who arrives.
- Agree in writing who supplies equipment such as scaffolds and protective gear.
- Carry out a joint job hazard analysis where two crews share an area.
- Check the work on site and review it when the job ends.
ISO 45001 covers this in its clause on procurement (clause 8.1.4), which asks organizations to coordinate with contractors so that hazards are identified and risks controlled.
How Should a Site Plan for Emergencies Such as a Collapse?
The first step is to list the emergencies the site could face. Depending on the work, that might include the collapse of a structure or an excavation, a fire, a fall from height, a serious medical event or flooding. For each one, the plan says who raises the alarm, who is in charge, where people meet and who is trained to give first aid or help with a rescue.
OSHA’s rule on emergency action plans for construction (29 CFR 1926.35) gives a useful checklist. The required elements are escape procedures and route assignments, procedures for employees who stay behind to run critical operations, a way to account for everyone after evacuation, rescue and medical duties, the preferred means of reporting emergencies and names or job titles of people who can be contacted for more information. The rule also asks employers to train enough people to help with an orderly evacuation and to review the plan with workers when it’s first written, when their duties change and when the plan changes. Because it’s an American rule, I’d use it as a model rather than as Nigerian law.
ISO 45001 adds that emergency plans should be tested periodically (clause 8.2). A short drill every few months, followed by a review of what went wrong, shows whether the plan works on the site as it stands today.
So far we’ve looked at what a system contains, and many companies organize it around an international standard. Let’s look at ISO 45001 and how it applies to construction companies in Nigeria.
How Does ISO 45001 Apply to Construction Companies in Nigeria?
ISO 45001 is the international standard for occupational health and safety management systems. It sets out requirements that an organization of any size can use to build the kind of system we’ve just looked at, from hazard lists and objectives to audits and corrective actions. The current edition is ISO 45001:2018.
Note: A new edition is on the way. A certification body called SQS reports that the revision has reached the Draft International Standard stage, with public consultation held from 16 June to 8 September 2026. It expects the final standard no earlier than April 2027. SQS says the existing structure will be kept, and the draft puts more weight on leadership responsibility, safety culture and psychosocial risks. It also says transition rules for certified companies haven’t been published yet, though a three-year transition period is usual. Anything built on the 2018 edition now should carry over, but it’s worth checking the final text when it’s released.
Is ISO 45001 Mandatory in Nigeria?
I didn’t find any Nigerian law or regulation that requires ISO 45001. An opinion article on AllAfrica from May 2025 describes it as a voluntary standard that organizations can adopt. The same article says the Factories Act of 2004 is still in force but is widely seen as outdated, and that a federal occupational safety and health act has been called for but hasn’t passed. It also notes that Lagos operates under its own State Safety Commission law. This is one commentator’s account, so for anything that affects your legal position, please confirm the current rules with the Federal Ministry of Labour or the Lagos State Safety Commission.
Even where the law doesn’t ask for it, a client or a tender may. That makes it worth reading the safety requirements in each contract you bid for.
What Does Occupational Health and Safety Certification Involve?
Certification means an independent body checks your system against the standard and issues a certificate if it meets the requirements. The steps are broadly the same in most countries:
- The company compares its current practice with the standard, which is called a gap analysis.
- It builds or repairs the missing parts of the system.
- It runs an internal audit and holds a management review, where senior managers go through the results.
- The certification body carries out a Stage 1 audit, which is usually a review of documents and readiness.
- It then carries out a Stage 2 audit, which checks on site that the system works in practice.
- If the audits go well, it issues a certificate, which is usually valid for three years, with surveillance audits in between.
A certificate shows that the system met the standard on the days it was checked. It doesn’t tell us how any single site performs from one month to the next, which is why the routines have to continue after the audit.
Which Bodies Can Certify, and How Long and How Much?
The Nigeria National Accreditation System (NiNAS) accredits certification bodies, which means it checks that they are competent to audit. According to an International Accreditation Forum news item dated 30 October 2025, NiNAS gained recognition from the Forum on 15 October 2025 for quality, environmental, occupational health and safety, and food safety management system scopes. NiNAS also publishes a list of accredited management system certification bodies, last modified in January 2025, which names System Certifications Limited, Interconformity Assessment and Certification Limited, CoreQuality CB Limited and NiCERT Limited. The list doesn’t say which standards each body is accredited for, so ask any body you’re considering to show its accreditation certificate and confirm that it covers occupational health and safety. If you’re looking at a body accredited elsewhere, ask the same question about the accreditation body behind it.
I couldn’t find independent, published figures for how long certification takes in Nigeria or what it costs. The pages that quote numbers are mostly from consultants selling services, so I haven’t used them. DEKRA, a certification body in the Netherlands, names the factors that drive audit time and cost: the number of employees, the number of locations and the risk level of the sector, with construction listed among the higher-risk ones. It also says a company that already holds an accredited certificate can transfer it, while a company starting from scratch goes through initial certification. DEKRA gives no prices, so the practical step is to ask at least two bodies for written quotes that state the number of audit days.
Can a Company Follow ISO 45001 Without Being Certified?
Yes. The standard is a framework, and a company can follow its requirements, run its own internal audits and hold its own management reviews without an outside body. It can then decide later whether a client, a tender or its own goals call for a certificate. Until a certificate has been issued, it’s more accurate to say a company follows the principles of ISO 45001 than to say it is certified.
That covers the standard and what certification involves. Next, let’s look at where a smaller contractor or field team can start.





